Orders placed Monday through Friday before 12:00 noon ET are typically shipped same day!

7104223 VALVE REPAIR KIT SET OF 6

More Views

$27.79

7104223 VALVE REPAIR KIT SET OF 6

Part Number: 7104223

Brand: AAA, OEM, DeWalt, Excell, Simpson, Delco

In stock

7104223 Valve Repair kit comes complete with 6 replacement valves.

The 7104223 Valve kit was used on the following FNA Group Pumps.

8.6VAC11 OEM TECHNOLOGY PUMP
90025 OEM TECHNOLOGY PUMP KIT

510001 OEM TECHNOLOGY PUMP
510011 OEM TECHNOLOGY PUMP

8.6CAV12 OEM TECHNOLOGY PUMP
510003 OEM TECHNOLOGY PUMP

8.6CAV12B OEM TECHNOLOGY PUMP
510005 OEM TECHNOLOGY PUMP

90026 OEM TECHNOLOGY PUMP KIT
8.6CAV12A OEM TECHNOLOGY PUMP

510014 OEM TECHNOLOGY PUMP
8.6CAH12B OEM TECHNOLOGY PUMP

90029 OEM TECHNOLOGY PUMP KIT
520002 AAA PRESSURE WASHER PUMP

90028 OEM TECHNOLOGY PUMP KIT
8.6CAH12A OEM TECHNOLOGY PUMP
520011 AAA PRESSURE WASHER PUMP

520004 PHOENIX 28 SERIES PUMP

520006 PHOENIX 28 SERIES PUMP

530001 AAA PRESSURE WASHER PUMP
90030 AAA PRESSURE WASHER PUMP

9.6GA12 AAA PRESSURE WASHER PUMP
530002-C-30 AAA PRESSURE WASHER PUMP

Each of the valves in the 7104223 kit has the following dimensions:
Metal base with "O" ring: .468" (11.887 mm)
Spring cage at top : .450" (11.430mm)
Length from metal base to the top of the spring cage: .550" (13.970mm)
Diameter of small projection on spring cage: .250" (6.350mm)
Length of small projection: .120" (3.048mm)
Total length of valve: .665" (16.891mm)

Description

This 7104223 Valve kit is compatible with the following pressure washer pumps:

AAA 8.7 GA Series Power Washer Pumps:

This 7104223 Valve kit is compatible with the following power washers from Dewalt: DXPW3025 Type 0 Gas Pressure Washer 3000 PSI @ 2.5 GPMT
DXPW3025 Type 0 Gas Power Washer 3000 PSI @ 2.5 GPM
DXPW3228 Type 0 Gas Power Washer 3200 PSI @ 2.8 GPM
DXPW3425 (Type 0) Professional Gas Cold Water Pressure Washer
BDG2600-B3 Type S/N 389386 to Present 2600 PSI Gas Pressure Washer
BDX2723-B3 Type 749685 to Present Version “A” 2700psi Gas Pressure Washer
BDX2723-B3 Type 749685 to Present Version “B” 2700psi Gasoline Power Washer
BDX3125-B3 Type 749685 To Present 3100 psi Gasoline Power washer
530016

Service Information
When removing your old inlet and outlet pressure valves it is very important to verify that all of the components of each the old valves have been completely removed. Make sure the plastic cage, pressure spring, round pressure disc and round metal seat with o-ring have all been removed. If all of these items have not been removed then damage will occur when the new valves are attempted to be installed. After removal of old components making up each complete inlet or outlet pressure valve clean out any debris from the valve cavity. Apply a small amount of grease or other suitable lubricant to each valve seat and o-ring. Then gently install the new valve assembly into the valve cavity and seat the valve completely to the bottom of the cavity. If needed a 3/8 drive 1/4 inch deep well socket will fit over the raised nipple on the top of the valve and allow the valve to be completely seated into position. When all six valves have been seated completely into position you may them proceed to the reassembly;y of the complete head to the pump body.